Kuwasiliana na Wasambazaji? Mtoa huduma
Nicolas Mr. Nicolas
Naweza kukusaidia vipi?
Msaidizi wa Mawasiliano
 Simu:86-0755-13828824221 Barua pepe:1650259446@qq.com
Home > Bidhaa > Mashine ya Kuingiza Panasonic > Mchanganyiko wa Sehemu ya Kuingiza ya Kinga ya Radial RL132
Mchanganyiko wa Sehemu ya Kuingiza ya Kinga ya Radial RL132
  • Mchanganyiko wa Sehemu ya Kuingiza ya Kinga ya Radial RL132

Mchanganyiko wa Sehemu ya Kuingiza ya Kinga ya Radial RL132

    Aina ya malipo: T/T
    Incoterm: FOB,CFR,EXW
    Min. Amri: 1 Bag/Bags
    Muda wa Utoaji: 7 Siku

Maelezo ya Msingi

Mfano wa Mfano.: NM-EJR5A, NM-EJR6A

Additional Info

Ufungaji: Ufungashaji wa utupu katika kesi za mbao

Brand: Panasonic

Usafiri: Ocean

Mahali ya Mwanzo: Japan

Bandari: Hong Kong

Maelezo ya bidhaa

Vipengele

RL132 ni mashine ya kuingiza sehemu ya radial na mfumo wa pini ya mwongozo wenye uwezo wa kuingiza kwa kasi kubwa wakati wa ufundi wa 0.14 s / sehemu,

ambayo pia husababisha kuokoa nishati na kelele ya operesheni iliyopunguzwa.
1.Urefu-kasi na Uingilivu wa juu-wiani
Kuingiza kwa kasi ya juu kwa wakati wa juu wa nambari ya 0,14 s / sehemu inaruhusu kuingizwa kwa wiani wa juu.
Viwango vya Operesheni vilivyoboreshwa
• Sehemu ya kulisha ya sehemu hutoa vifaa bila kusimamisha mashine ambayo inaruhusu operesheni ya saa zaidi.
• Kazi ya urejeshaji wa usambazaji wa kiotomatiki na huduma za programu pia huchangia kufanya kazi kwa muda mrefu wa mashine.
3.Kuaminika sana
Nafasi za kuingiza zinarekebishwa kwa msingi wa kukabiliana na kupatikana kwa njia ya utambuzi wa kuona wa shimo za kuingizwa kwenye bodi ya PC, kuhakikisha kuingizwa kwa uhakika.


Maelezo ya Mashine

Model ID RL132
Model No. NM-EJR5A NM-EJR6A
PCB dimensions (mm) L 50 x W 50 to L 508 x W 381
Max.speed 0.14 s/component
No.of component inputs 40 80 (Connection mode), 40 + 40 (Exchange mode)
Applicable components Pitch 2.5/5.0 mm (standard), 7.5 mm and 10 mm (option),
Resistor, Electrolytic capacitor, Ceramic capacitor, LED, Transistor, Filter, Resistor network
PCB exchange time about 2 s to about 4 s (Room temperature 20 °C)
Insertion direction 360°direction by 1°increment

Electric source *1

3-phase AC 200 V, 3.5 kVA
Pneumatic source 0.5 MPa, 80 L/min (A.N.R.)
Dimensions (mm) W 2 104 x D 2 183 x H 1 575 *2 W 3 200 x D 2 417 x H 1 575 *2

Mass *3

1750 kg   2350 kg



            Item                                                    Details
Power supply  Rated voltage        3-phase 200 / 220 V ± 10 V selectable
                              380 / 400 / 420 / 480 V ±20 V selectable
 Frequency             50 / 60 Hz
 Rated capacity       Approx. 3.5kVA
Air supply  Supplied air pressure      Min. 0.45 MPa to Max. 0.8 MPa
                                      (Operation air pressure: 0.45 ~ 0.5 MPa)
 Supplied air mass           Approx. 80 L / min. (A.N.R)
Note: Quick coupler attached (SMC KK13P-03M, KK13S-03F).
Dimensions  NM-EJR5A         W2,104 x D2,183 x H1,575 mm
                              (Not including signal tower)
 NM-EJR6A        W3,200 x D2,417 x H1,575 mm
                              (Not including signal tower)
Mass  NM-EJR5A        Approx. 1,750 kg (main body only)
 NM-EJR6A        Approx. 2,350 kg (main body only)
Environmental requirements  Ambient temperature       20°C ± 10°C
Operating controls  Interactive operation via color LCD touch screen
    English/Japanese/Chinese selectable with a single button Recognition screen
    (displays the recognized board image on a superimposed window)
    Hierarchical menu (Operator/Engineer)
 I /O functions        SD card slot
                              (standard equipment)
 Communication      LAN comunicaton (TCP/IP)
Coating color  Standard color    White: W-13 (G50)

Utendaji wa kimsingi

                              Item                                                                            Details
Insertion tact time  • Max. tact time: Approx. 0.14 s/point (0.17, 0.20, 0.25, 0.3 s/point  changeable)
 =REMARKS=

 *1 X-Y table movement at the tact time of 0.14 s/point: Within 36 mm Insertion       

      direction: each 1degree (0°- 90°, 0°- (-)90° : 0.14 s/point)

                                             (90°- 180°,91°- (-)180°: 0.20 s/point)

 *2 The tact time above is enabled only when components are continuousl              

      taped.  (Tact time varies if there are missing portions.)

 *3 Tact time varies between the beginning and the last of the insertion.
 *4 Tact time varies when new components are inserted for recovery.

 *5 Tact time varies also if 10 or more feeders are operated at a time due to the        

      NC data setting.

 *6 Tact time must be set between 0.25 and 0.30 s when inserting components        

      more than 12 mm in diameter or more than 18 mm in height

Applicable components

 Insertion pitch: 2.5 and 5.0 mm (standard), 7.5 and 10.0 mm (option)

 Height: Hn = Max. 23 mm

 Diameter: D = Max. 13 mm
 Resistors, electrolytic capacitors, ceramic capacitors, LEDs, transistors, filters   and resistor networks
Component packaging  • Taping (in pack or reel)
 =REMARKS=

 Component pack must be lower than 360 mm and width less than 62 mm.

 Component reel must be up to 360 mm in diameter and 62 mm in width.

 Bracket and reel shaft are required. Cannot be used on the upper stage of the   supply unit.
PCB replacement time  • Approx. 2 second (Ambient temperature: 20°C):
 =REMARKS=
 PCB replacement time only includes time for loading. It takes approx. 4 to 5   seconds including the table return time.
Applicable PCB  • Dimensions
   Min. 50 x 50 mm to Max. 508 x 381 mm

   Width-to-length ratio: Width should be equal to or less than length. 

   Consult us for boards having width longer than length.

 • Allowable insertion area
   Min. 50 x 40 mm ~ Max. 508 x 371 mm
 • Thickness
   1.6 mm ± 0.15 mm (for standard specification)
 =REMARKS=

 Boards of thickness from 0.6 mm (min.) to 2.0 mm (max.) are applicable. 

 Even if the board thickness is within the above range, clinched angle of 

 the  inserted lead or lead length may vary, or board transfer error may 

 occur depending on the shapes of board or insertion holes. Please contact 

 us in advance.


 • Mass
    Max. 1 kg per board including inserted components.
 • Flow direction
    Right to left (Standard) or Left to right (Option)
 • Board positioning method
    Pin positioning (Standard, without positioning in the Y direction),
 =REMARKS=
    Contact us separately for edge positioning.
Insertion pitch  • 2-pitch (standard), 3-pitch or 4-pitch (option)
   2.5 mm and 5.0 mm (standard),
   2.5 mm ,5.0 mm ,7.5 mm ,or 2.5 mm ,5.0 mm ,7.5 mm,10.0 mm (Option)
Insertion direction  • 360 degrees by 1 degree
Anvil  • Cutting & Clinch type system (Piezoelectric detection system)
No. of component inputs  • NM-EJR5A   40 types
 • NM-EJR6A   80 types

Maelezo ya Udhibiti

                            Item                                                         Details
Control system    Microcomputer system
Programming method    X-Y axes: Absolute coordinate commands
   Insertion pitch: Absolute commands
   Component feeder: Feeder number designation
Least command increment of X-Y table    0.01 mm / pulse
Program    Number of NC programs
   Built-in flash memory        200 programs, 5000 steps / program
    (Note: In case of programs involving pattern repeat, the total number
     of steps after expanding the program must be less than 5,000.)
   SD card                             Depends on the card capacity. (up to 2 GB)
Indication light    Signal tower (3 lamps, top to bottom: red/yellow/green)
Hole position offset    Determines optimum insertion positions based on the recognition of all
     insertion positions to make positional corrections (XY and q).
Self-diagnosis function    Presents on the color LCD the machine status when the power is ON and    
     situation of any troubles occurred, as well as countermeasures against the
     troubles.
Others    Programming functions Pana
    PRO J
    PanaPROJ the software for optimizing the balance of line consisting of
    multiple machines and for assigning data is available.
   Data compatibility

    Data from conventional RH series (RH, RH6, RHP, RHP2, RH2, RH3, RH5, RHSG, RHS, 

    RHS2, RHS2B, RHU, RHU2, RHUP, RG131 and RL131) can be directly used on the RL132.


= KUMBUKA =

Wh sw kupumzika tena baada ya kusimamishwa kwa muda mrefu, angalia ikiwa hakuna chochote kibaya na shughuli za mashine kwa njia ya mwongozo na kufanya kazi bila kazi.

Rl132 2

Shenzhen Keith Electronic Equipment Co, Ltd "iko katika Wilaya ya Baoan, Shenzhen. Ni muuzaji wa vifaa vya AI na SMT, vipuri, vinywaji na vifaa vya matumizi vya kusaidia nchini China. Kwa miaka mingi, tumetoa vifaa vya juu na sehemu kwa wateja wetu ili kuhakikisha huduma ya hali ya juu. Na kwa soko la kuuza nje, tunapanga kuendeleza Ulaya, Amerika ya Kaskazini, Amerika Kusini, Asia ya Kusini, India na mahali panapohitajika vifaa vya vifaa vya SMT.
Falsafa ya biashara: ushirikiano, kushinda-kushinda, uvumbuzi, msaada wa pande zote
Tumekuwa tukiandamana na dhana ya usimamizi wa chapa ya "kuzingatia ubora wa bidhaa na mahitaji ya wateja", kupitia utekelezaji wa uvumbuzi wazi, usimamizi bora wa operesheni, maendeleo ya rasilimali watu na mikakati mingine, ili kujenga kikamilifu ushindani wa msingi wa kampuni, kuunda wateja na maadili ya kijamii, na mshinde sifa moja ya idadi kubwa ya wateja na jamii.
Bidhaa kuu:
Mashine ya Kuingiza Paneli, Sehemu za Mashine ya Kuingiza Paneli, Mashine ya Kuweka Paneli, Sehemu za Mashine za Kuweka Paneli, Mchanganyiko wa Panasonic & Sehemu za Kulisha, Trolley ya Mchanganyiko, Mchanganyiko wa SMT nk Ili kupata maelezo zaidi juu ya bidhaa zetu, tafadhali wasiliana nasi kupitia anwani ya barua pepe ifuatayo. ushirikiano wako!

Jamii za Bidhaa : Mashine ya Kuingiza Panasonic

Barua pepe kwa muuzaji huyu
  • Mr. Nicolas
  • Ujumbe wako lazima uwe kati ya herufi 20-8000

Orodha ya Bidhaa zinazohusiana

Nyumbani

Phone

Skype

Uchunguzi